This is the o-ring seal found on the valve handle screw on the Norwalk juicer. Located under the screw that is found in the end of the pressure adjustment shaft. One of these is required per unit,

This o-ring is the seal for the hydraulic ram that extends during the pressing process. The o-ring is located in the hydraulic reservoir cover. To replace this o-ring seal, the cover must be removed to gain access to the O-Ring. One is required per juicer unit. This o-ring fits models 235 through 290 Norwalk juicers.

This o-ring is the seal for the hydraulic cylinder upper seal. The o-ring is located at the top hydraulic cylinder and is fitting to the reservoir cover groove. To replace this o-ring seal, the cover must be removed to gain access to the o-ring. One is required per juicer unit. This o-ring fits models 235 through 290 Norwalk juicers.

This o-ring is the seal for the hydraulic cylinder lower seal. The o-ring is located at the lower hydraulic cylinder and is fitting to the reservoir lower base groove. To replace this o-ring seal, the cover must be removed to gain access to the o-ring. One is required per juicer unit. This o-ring fits models 235 through 290 Norwalk juicers

This o-ring is the seal for the hydraulic ram piston groove. The o-ring is located on the piston. To replace this o-ring seal, the cover must be removed to gain access to the O-Ring. One is required per juicer unit. This o-ring fits models 235 through 290 Norwalk juicers.

The o-ring is located at the top hydraulic reservoir and is fitting to the reservoir cover groove. To replace this o-ring seal, the cover must be removed to gain access to the o-ring. One is required per juicer unit. This o-ring fits models 235 through 290 Norwalk juicers

This is the o-ring seal found on the top external face of the hydraulic reservoir on the Norwalk model 290 juicer. The seals purpose is to reduce juice leakage past the top stainless sheet metal and into the juicer's internal area.

These are a pair of o-rings that are located on the hydraulic pressure regulator shaft on a Norwalk juicer. They are located on the shaft within the packing nut assembly. Sold as a pair.

This hardware pack supplies you with all of the required bolts and washers needed during the removal and reinstall of the hydraulic reservoir in a Norwalk juicer. Here's what's included:

• The (6) bolts and washers for the reservoir cover
• The lower base attach bolt for securing the reservoir to the units base
• (2) extra long bolts for drawing down the reservoir cover during the reservoir reassembly

This group of components makes up the required internal assembly for hydraulic pressure regulation. Comprised of a ball bearing, spring and spacer shaft, these items are found on the center of the hydraulic regulator shaft. The assembly is accessed through the center of the shaft by removing the handle attach screw and removing th internal allen screw. These are sold as a set of three components.
*Note - By removing or adjusting the allen set screw, the machine hydraulic pressure will be adjusted. This should be done by a service technician. Hydraulic pressures are criticle to proper operation and safety of this unit.*

This is the complete o-ring set for the Norwalk juicer models 240 250 260 265 270 275 280 290. The set comes complete with the following o-rings:

• Lower cylinder o-ring
• Upper cylinder o-ring
• Ram o-ring
• Reservoir cover o-ring
• Piston o-ring
• Valve handle screw o-ring
• Valve shaft seals

This piston return spring, also known as a hydro spring, is a direct replacement for the spring found in the Norwalk 240-250-260-265-270-275-280-290 juicer models

This is refurbished valve handle is a direct replacement for the original valve handles for the Norwalk juicer models 240 250 260 265 270 275 280 290.

This is the replacement hydraulic shaft that has the pressure adjustment handle fastened to the external part of the shaft. The shaft is designed to have the internal spring, ball and spacer internally to adjust the hydraulic pressure needed to press the juice cloths.
* Note - This is for is the shaft only. This does not include the internals, packing nut, o-rings or the handle.

.

Made specifically for the Norwalk models 270 through 290, this piston and ram assembly is a direct replacement for the original part

This hydraulic reservoir and valve assembly fit the original Norwalk factory unit.